News

Thin Mini-ITX Mainboard for compact display systems.

With the Thin Mini-ITX Board PH12FEI, ICP Deutschland offers system integrators a motherboard to produce particularly flat displays or embedded systems. The PH12FEI is equipped with an IO Shield at half height and horizontal memory slots, which bring it to a height of only 20 mm.

The LGA1151 socket installed on the PH12FEI supports the entire Intel® Coffee Lake processor series from CoreTM i7/i5/i3 through Celeron® to Pentium®. ICP offers a functionally fully equipped Q370 chipset variant as well as a reduced and less expensive H310 variant. The two SO-DIMM slots allow up to 32Gb DDR4 memory to be operated in dual channel mode. A DisplayPort 1.2 with 4K, an HDMI 1.4 with 4K and an LVDS port with Full HD resolution are available for the connection of displays. The LVDS can be replaced by an optional eDP with 4K resolution.

The PH12FEI offers a PCIe x4 slot as well as a M.2 2280 and a M.2 2230 slot. Two GbE...

Designed to please.

With the D210-11KS, ICP Deutschland launches a 21.5" all-in-one PC that focuses on design. The attractive front is equipped with a projected capacitive flat touch. The optional accessories have the same design. This also results in an attractive uniform front with installed webcam, RFID, barcode scanner or SMART Card and magnetic card reader. There is also room for the accessories to be mounted. The accessories can be mounted flush all around the front. The standard version of the D210 is equipped with a Kaby Lake U i3 processor. Celeron® and other Core-I Kaby Lake U or Skylake U versions are optionally available. Equipped with up to 32GB RAM...

Mobile panel PC for medical use.

ICP Germany offers a new Panel PC series especially for mobile use in medical environment.

The POCm-W can be equipped with up to three Li-ION battery packs to provide a runtime of 8 hours. The Hot Swap function and the optional battery docking station allow the battery life to be extended at will. Compared to conventional visit wagons with LiFePO4 battery units, the use of Li-ION batteries allows a weight saving of more than 5 kilograms.

The POCm-W is available in the display sizes 21.5" and 23.8" with a resolution of 1920x1080 and a projected-capacitive touch. The Touch is optimized for the use of multi-layer gloves and the detection of splash water and water drops. The housing is anti-bacterial, offers an IP65 front protection and a back with IP32 protection. A passively cooled version with Intel® mobile ULT Core™ i7-6600U, i5-6300U and Celeron® 3855U is offered. The POCm-W is pre-equipped with 4GB DDR4 RAM and can be extended up to 32GB. For storage media, both a 2.5" SATA drive bay accessible from the outside and two M.2 interfaces with RAID functionality are available. Furthermore...

More Performance with Mature Whiskey Lake Processors.

ICP Deutschland launches the high-performance EPIC embedded board NANO-ULT5 with Intel® Whiskey Lake processors. The refresh of the 8th Gen. Intel Core I processors are manufactured in the mature 14 nanometer technology. Higher turbo boost clock rates offer a performance gain compared to the predecessor.

The NANO-ULT5 board is offered in one variation with Celeron®, Intel Core i3, i5 and i7. Up to 32Gb DDR4 RAM in Dual Channel Mode are supported. Furthermore a display port and an HDMI port with a max. resolution of 3840x2160 as well as an LVDS port with a max. resolution of 1920x1200 are available. Further performance increases...

Industrial 16:9 wide screen monitors.

The DM-F industrial monitor series from ICP Germany is growing literally. The current 3:4 format of the 6.5" to 19" display sizes is extended by the 16:9 format for the medium display sizes 15.6" and 18.5". Thus the DM-F series gains two further wide screen monitors with a WXGA resolution of 1366x768 pixels in addition to the existing 21.5" and 23.8" monitors. The DM-FW variants are available either as resistive touch or projected capacitive touch with anti-glare and anti-UV protection.

The aluminum front panel is IP65 protected. The...

Interface miracle for machine control

In machine control, road traffic control and robotics, the demand for versatile analog interfaces is almost limitless. The new fanless Embedded PC TANK-620 from the proven TANK series from ICP Germany was designed for this field of application. The interface miracle has six RS-232, eight RS-422/485 and four USB 2.0/3.0 ports each. The 14 COM ports are equipped with TX/RX signal LEDs so that the current data transmission can be displayed. In addition, two GbE LAN interfaces and 12 digital inputs and 12 digital outputs are available at the front. Inside the compact 260x200x100mm housing is an Intel® Celeron® 3855U processor with 4GB DDR4 on-board memory, which can be expanded up to 32GB. As standard, the TANK-620 has two VGA in Full-HD resolution for parallel image output. A third optional screen output is provided as VGA or LVDS interface. On the one hand, two easily accessible 2.5" SATA 6Gb/s hard disk bays, an M.2 slot and an optional...

Industrial 3D NAND SSD - Reliable, High Capacity and Cost-Effective

3D NAND Flash Solid State Disks (SSD), which are based on Triple Level Cell (TLC) memory cells, have so far only been used sporadically in industrial applications.

With the new Titan T351 series, ICP Germany is launching a TLC SSD family on the market that is reliable, high-capacity and cost-effective. By combining memory cells from market leader Toshiba and firmware from Cervoz with a low-density parity check ECC algorithm, the Titan series offers high quality standards and particularly high data integrity.

The T351 series includes all form factors from 2.5" through mSATA to M.2 (2242/2280) and is compatible with the SATA 6Gb/s standard interface. What stands out in comparison to the current MLC M305 SSD family is the double write and read speed of up to 510/560MB/s. In addition to the standard capacities of 64Gb to 512GB, a 1TB size is also available. Also the T351 series...

19" PC System with 56 PCI-Express Lanes

Whether an AI training system or a high-performance system for image processing, rendering or mining, the requirements for performance, data storage capacity and transmission speed are almost exorbitant. The 19" PC system GRAND-C422 from ICP Germany offers the solution.

The GRAND-C422 can be equipped with a 4 to 18 core processor of the Intel® Xeon® W family based on the LGA2066 socket. A compact and highly efficient water cooling system was implemented as CPU cooling, which can dissipate up to 250W TDP waste heat. The DDR4 main memory can be flexibly expanded from 32GB to 256 GB depending on the computing power required.

The high performance of the GRAND-C422 is also reflected...

Slot CPU card with 56 PCI Express Lanes.

The new PEMUX-XEW1 slot CPU card from ICP Germany is suitable for high-performance computers that are to accommodate several graphics or FPGA plug-in cards. The PEMUX Slot CPU card with its 56 PCI-Express lanes and the corresponding backplanes offers various possibilities to build high-performance systems.

The PEMUX-XEW1 is a 12-layer slot CPU card and defines a new standard among slot CPU cards. It is equipped with an LGA 2066 socket that supports Intel® Xeon W processors with up to 28 cores. The four DDR4-RAM slots can accommodate a maximum of 256 GB ECC RDIMM or LRDIMM memory modules. Furthermore, the PEMUX offers eight SATA 6GB/s ports for the use of all common storage media. An M.2 2280 slot with a PCI Express x4 signal extends the possibility of equipping the system with solid state storage discs. Data security is not neglected either. In addition to the RAID 0/1/5/10 functionality, the PEMUX card offers a TPM2.0 port and an internal USB DOM header for the use...

FPGA for Deep Learning Inference.

The FPGA-based Mustang-F100 accelerator card from ICP Deutschland is designated for industrial inference systems. It is primarily used for deep learning inference in real time, for video and image processing as well as for the analysis of machine and sensor data.
The Mustang-F100 is based on the Intel® Arria® 10 GX1150 FPGA and is equipped with 8GB on-board DDR4 RAM. Due to its parallelism and its high degree of configuration, which is inherent in the FPGA, the Mustang-F100 can handle changing workloads and different floating-points. It also supports a variety of topologies such as AlexNet, ResNet or Yolo Tiny. From classic object recognition to video and image classification to facial recognition or image...